Nov 1, 2015 - Then install the Cleanflight Configurator from the Chrome Web Store and download the latest Cleanflight firmware.bin file for the CC3D board. Flashed the cc3d opbl.bin file onto the cc3d. Powered the board and connected to clean flight it says connecting then says failed no data.
Cleanflight v2.5.0 Latest Cleanflight Configurator = v2.5.0-RC1 is required. Changes since v2.5.0-RC1:. None Changes since v2.4.1:. Added support for feed forward to the PID controller. Improved the performance of the dynamic notch filter. Changes from Betaflight 3.5.2 merged - see Betaflight release notes for details.
Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:.
Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Use of motor outputs 5-8 on SPRacingF7DUAL requires 'NOVTX' firmware, get it here: Future:.
Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers.
OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC. Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board.
Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual.
Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers.
Everyone that has donated to the Cleanflight project. All configurator versions are available here. Cleanflight v2.5.0-RC1 Latest Cleanflight Configurator = v2.5.0-RC1 is required. Changes since v2.4.1:. Added support for feed forward to the PID controller. Improved the performance of the dynamic notch filter. Changes from Betaflight 3.5.2 merged - see Betaflight release notes for details.
Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator.
OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:.
Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing.
The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Use of motor outputs 5-8 on SPRacingF7DUAL requires 'NOVTX' firmware, get it here: Future:. Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers.
OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC. Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board.
Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards.
Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:.
All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project.
All configurator versions are available here. Cleanflight v2.4.1 Latest Cleanflight Configurator = v2.4.0-RC1 is required. Changes since v2.4.0:. Fixed SPRACINGF3OSD slave 'Waiting for FC'. Changes since v2.4.0-RC1:. None, if you have flashed v2.4.0-RC1 you do not need to re-flash. Changes since v2.3.2:.
Enhanced flight performance. Changes from Betaflight 3.4 merged. Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See.
OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:. Manual needs updating, volunteers wanted!.
If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command.
Use of motor outputs 5-8 on SPRacingF7DUAL requires 'NOVTX' firmware, get it here: Future:. Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC.
Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'.
Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project.
All configurator versions are available here. Cleanflight v2.4.0 Latest Cleanflight Configurator = v2.4.0-RC1 is required. Changes since v2.4.0-RC1:. None, if you have flashed v2.4.0-RC1 you do not need to re-flash. Changes since v2.3.2:. Enhanced flight performance. Changes from Betaflight 3.4 merged.
Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator.
OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:. Manual needs updating, volunteers wanted!.
If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect.
See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command.
Use of motor outputs 5-8 on SPRacingF7DUAL requires 'NOVTX' firmware, get it here:. OSD Slave always says 'Waiting for FC', see Future:. Cleanflight will end support for F1 based boards soon. SAFETY:.
When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC. Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode.
Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:.
Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project. All configurator versions are available here. Cleanflight v2.4.0 Latest Cleanflight Configurator = v2.4.0-RC1 is required. Changes since v2.3.2:. Enhanced flight performance.
Changes from Betaflight 3.4 merged. Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:.
Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Future:. Cleanflight will end support for F1 based boards soon.
SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC.
Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts.
(Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:.
All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project. All configurator versions are available here.
Cleanflight v2.3.2 Latest Cleanflight Configurator = v2.2.0-RC1 is required. Changes since v2.3.1:.
Fix PWM RX 100% cpu usage issue. Changes since v2.3.0:. Fix missing transponder support for SPRacingF7DUAL. Changes since v2.2.0:. Flight performance enhanced. Added PID-Audio feature.
Many many many other changes and performance enhancements. Changes from Betaflight 3.3 merged. Improvements for OSD slave. Notes:.
Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave.
Known Issues:. Enabling Dynamic Filtering on F7 causes lock-up -. Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect.
See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command.
Future:. Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:.
Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC. Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards.
Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'.
Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project. All configurator versions are available here.
Cleanflight v2.3.1 Latest Cleanflight Configurator = v2.2.0-RC1 is required. Changes since v2.3.0:. Fix missing transponder support for SPRacingF7DUAL. Changes since v2.2.0:.
![]()
Flight performance enhanced. Added PID-Audio feature. Many many many other changes and performance enhancements. Changes from Betaflight 3.3 merged. Improvements for OSD slave.
Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less.
See. OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:. Enabling Dynamic Filtering on F7 causes lock-up -.
Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing.
The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Future:. Cleanflight will end support for F1 based boards soon.
SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC.
Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts.
(Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers.
Everyone that has donated to the Cleanflight project. All configurator versions are available here. Cleanflight v2.3.0 Latest Cleanflight Configurator = v2.2.0-RC1 is required. Changes since v2.2.0:. Flight performance enhanced. Added PID-Audio feature.
Many many many other changes and performance enhancements. Changes from Betaflight 3.3 merged. Improvements for OSD slave. Notes:. Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator.
OSD Slave users should upgrade both the FC and their OSD Slave. Known Issues:. Enabling Dynamic Filtering on F7 causes lock-up -.
Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing.
The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Future:. Cleanflight will end support for F1 based boards soon.
SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:. Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC.
Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual.
Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers.
Everyone that has donated to the Cleanflight project. All configurator versions are available here.
Cleanflight v2.3.0-RC1 Latest Cleanflight Configurator = v2.2.0-RC1 is required. Changes since v2.2.0:.
Flight performance enhanced. Many many many other changes and performance enhancements. Changes from Betaflight 3.3 merged. Improvements for OSD slave. Notes:.
Some features are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See. OSD users should use the latest font from the latest configurator. OSD Slave users should upgrade both the FC and their OSD Slave.
Known Issues:. Enabling Dynamic Filtering on F7 causes lock-up -. Manual needs updating, volunteers wanted!. If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect.
See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Future:. Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers. OSD Slave usage:.
Flash CF v2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC. Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode.
Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual. Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:.
Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Thanks:. All contributors, especially the core CF/BF developers. Everyone that has donated to the Cleanflight project. All configurator versions are available here. Cleanflight v2.2.0 Latest Cleanflight Configurator = v2.1.0-RC1 is required.
Changes since v2.2.0-RC2:. Add support for SPRACINGF7DUAL with DUAL SIMULTANEOUS GYROS.
Changes since v2.2.0-RC1:. Various bug fixes. Support for additional targets. Changes since v2.1.0:. Flight performance enhanced.
Many many many other changes and performance enhancements. Notes:.
Mag and Baro disabled by default for maximum flight performance. Default ESC protocol in CF2.x is ONESHOT, not PWM - see SAFETY NOTE. Some features, like GPS and SONAR, are disabled for some older targets like the NAZE32 and other targets with 256K flash or less. See.
OSD users should use the latest font from the latest configurator. Known Issues:. Manual needs updating, volunteers wanted!.
If you encounter issues with your settings not being correct after upgrading to the RC please report this via the feedback issue, then reset your settings and continue testing. The mixer setting in the configurator may not have any effect. See - configure a custom mixer and use the mmix cli command, see manual. Motors outputs need to be configured as servo outputs before using servos via the cli resource command. Future:.
Cleanflight will end support for F1 based boards soon. SAFETY:. When upgrading follow this simple procedure: Disconnect battery, remove propellers, flash/upgrade, configure, connect battery, test rx, test motors, test arming - only then should you re-attach your propellers.
OSD Slave usage:. Flash CF2.x onto a compatible stacking FC (SPRACINGF3, SPRACINGF4EVO, SPRACINGF3EVO). Enable OSD feature on the FC.
Enable MSP on UART1 on the FC. Flash CF2.x onto the SPRACINGF3OSD/PDB board. Upload Cleanflight font to the SPRACINGF3OSD using the 'OSD' tab, set video mode. Connect FC + OSD using stacking pins and power on board boards. Configure FC as usual.
Set the current sensor source to 'MSP sensor/OSD Slave'. Access OSD menu using sticks by following on-screen prompts. (Yaw Left, Throttle Mid, Pitch Up) User Support / Questions / Help:. Slack, Forums, Documentation, Facebook, IRC, BetaFlight WIKI Bug Reports ONLY:. Thanks:. All contributors, especially the core CF/BF developers.
Everyone that has donated to the Cleanflight project. All configurator versions are available here.
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |